These IP676 rated DC-DC
converters are not hermetically sealed, but they are fully IP676 ingress
protected, including immersion. They have a wide operating temperature range,
and use a single military style circular bayonet connector which contains both
input and output terminals. The wide input voltage range allows use in 12V or
24V systems, and designed to allow the use of 36 volt equipment in 12 volt, 14
volt, and 24 volt vehicles, marine, military, boat, yacht, PLC, and cell tower
applications. These are attractive, reliable, robust DC/DC converters good for
fork lifts, off-road, construction and recreational equipment. They are
relatively immune to vibration and shock.
To determine the output amps
you need just add up the watts of all the equipment and divide by 13.6V.
These converters are fully isolated and can be used for all 12 volt and
24 volt systems, including negative ground, positive ground, and floating
ground installations.
| DC-DC Converters |
60 Amp
DC to DC Converter
 |
Part
Number
and Price |
PSEC-884HS
$1360
|
| 6 foot cable
with connector |
Connector and
PSEC-68-0749-6
$295 each
|
| Connector
only |
CA3106E24-11SB NATO connector without cable
$110
each
One cable is used
|
| Nominal Input
Voltage |
24VDC, 32V, 36V and 24VDC |
| Input Voltage
range |
22 to 60VDC |
| Max Input
current at No Load |
<160 mA |
| Output
voltage |
13.6V |
| Output voltage
adjustment by removing the front plage |
11.8 VDC to 14.5 VDC |
| Max Output
Current(s) |
60 Amps for output voltages set between 12V and 14V |
| Max Output
Power; the actual output current depends on the ratio between the input and
output voltages. |
Maximum Output power =
Vout * 20 amps
For example 42 volts *
20 Amps = 840 Watts |
| Maximum Output
Power, Surge |
1000W |
| Max Output
Power (continuous) |
850W |
| Output current
limit? |
110% of maximum current with continuous automatic retry, 1000W peak
for short pulses |
| Operating
Temperature Range at 100% load |
-40°C to +70°C |
| Operating
humidity |
0-100% |
| Efficiency |
>95% over entire output range |
| Load Regulation
|
<200mV with remote sensing |
| Maximum input
current |
32A |
| Switching
frequency |
kHz |
| Output ripple
noise |
<50 mV rms |
| Isolation |
Common ground |
| Remote power
on/off |
Yes, through grounding a wire on the connector |
| Remote voltage
sense |
Yes. through two sense wires on the connector |
| Ingress
rating |
IP676, (dust tight, immersion up to 1 meter depth, 1 Joule
mechanical impact energy) |
| Connections |
Mating connector is the Canon 3106E24 - 11SB. See the connection
diagram below |
| Protection |
Low input voltage < 10.5 +/-0.3 VDC,
High input voltage
>61.0 VDC
Over temperature by internal thermostat, self resetting |
| Cooling |
Through convection and the baseplate |
| Dimensions |
15.5 x 8 x 2.95inches
39.4 x 20.3 x 7.4 cm |
| Fuse can be
accessed by removing the front cover |
ATC-30 |
| Drawings |
See below |
| Weight |
5.5 kg (12 lbs) |
| Audible
Noise |
None |
| Warranty |
2
years limited warranty for parts and labor |
PSEC-884HS drawing:
:
Heavy Duty, High Current Switchmode 24VDC/ 12VDC Converters.
Wide input voltage range suitable for 24 Volt, 32 Volt 36 Volt and 48 Volt
systems. |
