|
This battery charger is a
microprocessor controlled unit designed exclusively for charging a 1 cell 3.6
or 3.7 volt Lithium-ion battery pack. It has led indicators which indicate the
current operating mode of the charger. This battery charger complies with
applicable safety agency requirements.
Note: this product
is being replaced by the PST-3P10-L0504S, which is
identical electronically, but is wall-mount. When the current stock is gone the
product will be obsoleted.
| General
Information |
| Model |
PST-3P10-L0504 |
| Name |
1 Cell Lithium ion battery
charger |
| Type |
Battery Pack Charger for R/C,
instruments |
| ROHS |
ROHS available on special
order |
|
| |
| Technical
Information |
| Rated input voltage |
100-240 VAC, 50/60
Hz |
| No. of batteries |
1 cell lithium ion
or lithium polymer battery charger |
| 1 cells |
3.7 volts nominal,
4.2 volts peak during charge |
| Battery size |
100 mAH to 4000
mAH |
| Charging current |
800mA during CC or
constant current mode |
| Charge end current |
<110 mA |
| Charger type |
Li-ion/Li-Po
Battery Charger |
| Application |
R/C Models,
instruments |
| Charging algorithm |
Constant
current/Constant voltage |
| Input voltage |
100-240VAC |
| Input Frequency |
50-60 Hz |
| Maximum input power |
6 Watts |
| Battery type |
LiIon/LiPo |
| Style |
Desktop |
| Output power |
4W maximum |
| Output voltage |
4.2 volts peak |
| Output options included |
5.5 x 2.1 mm barrel
or alligator clips, others upon request |
| Plug wiring |
Inside
positive
Outside negative |
| Weight |
120 grams, 4 oz,
0.26 lbs |
| Cooling |
No fan, natural
convection cooling |
| Efficiency |
>60% |
| Size |
75 x 51 x 28 mm, 3 x
2 x 1 inches |
| Environment |
-10°C to
+40°C operating, -40°C to +70°C storage |
| Temperature rise |
<40°C rise on
case under any line voltage and maximum rated load |
| Vibration, Impact |
5mm, 50Hz, 600
Seconds, 1 meter drop 3 times |
| Protections |
Limited Power Source
(LPS), short circuit protected |
| Safety |
GB4943, UL1950,
EN60950, CE, double insulated, cUL, indoor use, LPS 50VA |
| EMI |
EN55022B |
| MTBF |
30,000 hours by
MIL-STD calculation |
| HiPot, ESD |
Hi-Pot 3000 V, 1
minute, ESD 3000V |
| LED Indications |
Charging |
Red |
|
Charged/Idle |
Green |
|
Flashing |
Error |
| Protections |
Short circuit
protection
Reverse polarity protection |
| AC power cord |
6 foot cord with
USA two prong plug |
|
|
Twelve optional DC Plugs slip over
the 5.5 x 2.1 mm connector if desired. |
 |
- 2.35 OD x 0.7 ID Barrel
- 3.0 OD x 1.1 ID Barrel
- 3.5 OD x 1.35 ID Barrel
- 4.0 OD x 1.7 ID Barrel
- 4.75 mm OD x 1.75 mm ID Barrel EIAJ-03
- 5.0 mm OD x 3.5 mm ID with center pin
- 5.5 mm OD x 1.5 mm ID type 2 Barrel
- 5.5 mm OD x 2.5 mm ID Barrel
- 6.3 OD x 3.0 ID center pin Barrel
- 6.0 OD x 4.4 ID center pin Barrel
- 7.4 mm OD x 5.0 center pin ID Barrel
- 7.9 OD x 5.6 ID center pin Barrel
|
|
Specifications:
Input Voltage: 100 - 240 VAC, 50/60 Hz.
Output Voltage: Up to 4.2 Vdc controlled by charger
Output current: 0.8 A ±0.1 A maximum, controlled by
charger
Temperature: -10 to +45° C, Operating -40 to +70° C,
non-Operating
Humidity: Indoor 90% R.H. @ 35° Celsius, Non-Condensing
|
|
